## Navigation

- FAQ Home
- All categories
- Instructions
- Section 1.0 - General
- Section 2.0 - Loads
- Section 3.0 - Analysis
- Section 4.0 - Design Strength of Structural Steel
- Section 5.0 - Manufacturing
- Section 6.0 - Other Structural Materials
- Section 7.0 - Guy Assemblies
- Section 8.0 - Insulators
- Section 9.0 - Foundations and Anchorages
- Section 10.0 - Protective Grounding
- Section 11.0 - Obstruction Marking
- Section 12.0 - Climbing Facilities
- Section 13.0 - Plans, Assembly Tolerances and Marking
- Section 14.0 - Maintenance and Condition Assessment
- Section 15.0 - Existing Structures
- Section 16.0 - Installation
- Annex A: Procurement and User Guidelines
- Annex B: U.S. Country Listings of Design Criteria
- Annex C: Design Wind Force on Typical Antennas
- Annex D: Twist and Sway Limitations for Microwave Antennas
- Annex E: Guy Rupture
- Annex F: Presumptive Soil Parameters
- Annex G: Geotechnical Investigations
- Annex H: Additional Corrosion Control
- Annex I: Climber Attachment Anchorages
- Annex J: Maintenance and Condition Assessment
- Annex K: Measuring Guy Tensions
- Annex L: Wind Speed Conversions
- Annex M: SI Conversion Factors
- Annex N: References
- Appendix 1: Design Criteria Maps
- TIA-222-F
- Miscellaneous
- Rejected Questions
- TIA-1019-A/TIA-322
- Sitemap

25 users online :: 25 Guests and 0 Registered

### Records in this category

- Section 13.3 question regarding plumb measurement of monopoles; submitted 7/20/2011
- Is there a tolerance recommendation for base plate to monopole connections? If the base plate is not perfectly perpendicular to the monopole, then the pole is installed out of plumb until it is plumbed up with leveling nuts. At this point the base plate is not level. What is the recommended tolerance for how out of level the base plate of a monopole can be?
- I have a tower for which the plumb and twist was recently taken by a registered surveyor. The initial Plumb and twist for the first two sections are out by a significant amount. The first two sections were stick built and it looks like the concrete foundation is not level. Is there an exemption to cover this?

### Tags

### Sticky FAQs

- How do I use this Site?
- Do we have to do a structural analysis on ...
- Does the Standard apply to the design of antennas? ...
- How to submit a question?
- Section 2.6.9.2What does the term “In the absence of ...
- Section 2.6.9.2Is it acceptable to use the results of ...
- Section 2.6.9.2Can I use loading that is less than ...
- Section 2.6.9.2Is it acceptable to use the results of ...
- Section 13.3 question regarding plumb measurement of monopoles; submitted ...
- Figure A1-1 Why were the tables and Note 3 ...
- 1) I knew this table 4-8 is used to ...
- 2.6.7.4 Gust Effect Factor for Structures Mounted on Other ...
- Is there reciprocity between ANSI/TIA-222-G and CSA S37-01? In ...
- Section 15.5 indicated "A feasibility report shall state ...
- Section 2.6.6 Calculating the topographic factors
- As everyone is aware, many jurisdictions are now adopting ...
- Section 2.7.3 states “Further, …earthquake effects may be ignored ...
- I am currently working a telecommunications tower project where ...
- Is there a tolerance recommendation for base plate to ...
- in case of telecommunication tower to be built on ...
- Is there a tolerance recommendation for base plate to ...
- in case of telecommunication tower to be built on ...
- The definition of Z in sections 2.6.5.2, 2.6.6.4, and ...
- If Ca=1.5 is used for a rectangular cluster of ...
- Section 2.6.5.2 “Velocity Pressure Coefficient”Question: Shall “z” in the ...
- Section 4.9.9: I'm using this section to calculate the ...
- Section 2.6.6.4 - Rev-G provides a simplified method of ...
- WHICH IS THE unbraced length "L" TO CONSIDER, ACCORDING ...
- Does section 2.8.2 Limit State Deformations of ANSI/TIA 222-G ...
- Where it has been suggested in previous posts that ...
- We understand section 2.6.4.1 to apply only to areas ...
- Waveguides, downleads, and other cables are frequently strapped to ...
- Should step pegs and safety climb be included in ...
- Section 3.6.2 note 1 regarding pattern loading and tower ...
- Approximately when will the next revision or amendment to ...
- I have a tower for which the plumb and ...
- In Section 4.4.1 of TIA/EIA-222-G December 2009 the minimum ...
- Section 3108.1 of the 2012 IBC eliminates the 222-G ...
- Section 9.6 What is the intent of the grade ...
- One thing I recently noticed was in Table C1, ...
- Regarding recent FAQ 1128: would it be possible to ...
- I’m trying to determine if a pad & pier ...
- Is it the intention of drafters of the TIA ...
- Section 2.6.5: Addendum 2 defines Exposure Category C as ...
- Section 5.4.2 gives requirements for Non Pre-Qualified Steel stating ...
- Which of the states adhere to the Rev G ...
- In Section 4.5.1, the following language is used:"A multiple ...
- Shall “z” in the equation be based on mid-height ...
- Section 4.9.9: I’m using this section to calculate the ...
- Section 2.6.6.4 - Rev-G provides a simplified method of ...
- Which is the unbraced length to consider, according to ...
- I am a commercial building reviewer for the City ...
- Does section 2.8.2 Limit State Deformations of ANSI/TIA 222-G ...
- Can section 2.8.2 also be applied to a TIA-222-F ...
- Table 4-6 provides slenderness requirements for horizontal members, specifically ...
- Where it has been suggested in previous posts that ...
- One thing I recently noticed was in Table C1, ...
- In Section 4.5.1, the following language is used:"A multiple ...
- Is it acceptable to use Ka = 0.6 for ...
- For double angles, are the modified (KL/r)m equations shall ...
- K is not mentioned on the right side of ...
- Is (KL/r)o shall include the curves defined in Table ...
- Section 4.9.8. Does the definition of Guy Assembly Link ...
- Section 12 Climbing Facilities in TIA-222-GWhat is the strength ...
- Section 12 Climbing Facilities TIA-222-GWhat is the strength requirement ...
- Section 4.5.3 Built-Up Members states that "A minimum of ...
- Referencing Section 2.3.2, Exception 4 and Note 3; for ...
- Is there any back up material for the usage ...
- I am a structural engineer in Oregon, and I ...
- Section 2.6.1: In the definitions section of 2.6.1, a ...
- Does TIA-222-G include any consideration of loads other than ...
- Should mounts be subjected to Section 15 requirements that ...
- Hello,The effective projected area of transmission lines mounted in ...
- Section 2.6.9My question is regarding how to determine the ...
- Hello. A question was asked about the validity of ...
- The inspection intervals are recommended. Can I extend the ...
- Is there any available document or article that explains ...
- Section A.2.2 and Table 2-1 establish the classification of ...
- Section A.2.2 and Table 2-1 establish the classification of ...
- The industry is on the verge of the release ...

## Section 13.0 - Plans, Assembly Tolerances and Marking

ID #1118

## Is there a tolerance recommendation for base plate to monopole connections? If the base plate is not perfectly perpendicular to the monopole, then the pole is installed out of plumb until it is plumbed up with leveling nuts. At this point the base plate is not level. What is the recommended tolerance for how out of level the base plate of a monopole can be?

The TIA STANDARD does not provide tolerances for monopole base plates.

**Tags: ** base plate, monopole, tolerance

**Related entries: **

- Some antenna manufacturers provide flat equivalent area and few of them just provide the dimensions. How can we address the CaAa without ice and with ½” ice for discrete appurtenance without flat equivalent area known?s
- Section 4.6.3.2 question regarding shear lag factor; submitted 9/15/2010
- Section 15.4 question regarding Changed Conditions Requiring a Structural Analysis; submitted 2/14/2007
- Section 13.3 question regarding plumb measurement of monopoles; submitted 7/20/2011
- 1) I knew this table 4-8 is used to calculate the polygonal tubular member yield stresses. Note 1. indicated "For polygonal members, w/t shall not exceed 2.14(E/Fy)^(1/2)". I saw other engineers still using the table to calculate the pole yield stress even the w/t ratio exceeds 2.14(E/Fy)^(1/2) limit. My understanding is once the w/t limit exceed, the pole will have local buckling issues and the pole will be failing. I just want to make sure there is not any addendum to the standard so the local bucking can be ignored.
- Section 2.6.6 Calculating the topographic factors
- Is there a tolerance recommendation for base plate to monopole connections? If the base plate is not perfectly perpendicular to the monopole, then the pole is installed out of plumb until it is plumbed up with leveling nuts. At this point the base plate is not level. What is the recommended tolerance for how out of level the base plate of a monopole can be?
- I am currently working a telecommunications tower project where dead weight of concrete blockswill be used to resist uplift and sliding forces at the base of a truss tower. These blocks of concretemust be placed above the soil.Provision 2.3.2 of TIA‐222‐G, Equation 2 shows the load combination of .9D + 1.0 Dg + 1.6 W. Sincethe dead load contributed by the concrete foundation and the steel tower above is the actualweight of concrete (not some assumed dead load used for the design of superstructure), is itnecessary to reduce the dead load of the concrete footing by 10%? Is there an ASD loadcombination (where wind load is not multiplied by 1.6) that can be used to calculate the requiredcounter weight?
- WHICH IS THE unbraced length "L" TO CONSIDER, ACCORDING TO SECTION 4.5.4.2., FOR TUBULAR POLE STRUCTURES WHERE SECTIONS DIFFER IN DIAMETER AND/OR THICKNESS
- Does section 2.8.2 Limit State Deformations of ANSI/TIA 222-G apply to the tower structures, or does it apply to appurtenances only? If this displacement limit applies to tower sections, in the case of a stealth monopole tower would the 3% limit be applied over the whole height of the tower (tower+stealth section) or should it be applied over just the stealth section?Can section 2.8.2 also be applied to a TIA-222-F structural analysis since currently this code does not include any displacement limits?Thanks,

Author: Jacob Proctor

Revision: 1.0

You cannot comment on this entry